Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGate Company in Temple City, CA
Temple City gate work is different because the housing stock is different. Most homes here were built between the 1940s and 1960s, and many still have their original wrought-iron pedestrian and driveway gates. That means our Gate Installation work often starts with a conversation about old concrete footings, rusted steel, and whether the existing gate should be restored or replaced. The hot, dry San Gabriel Valley summers warp wood and bake paint, while winter rains accelerate rust on unprotected iron. Call (855) 490-6590 for a free estimate on any gate project in Temple City.
Why Temple City Homes Are Different
Temple City’s residential streets are lined with mid-century ranch-style and traditional single-family homes on compact lots. A large share of those properties still have the original front-yard gates installed when the house was built. Those gates are now 50 to 80 years old. The wrought iron has rusted at the hinge and latch points. The concrete post footings, poured in an era before modern reinforcement standards, have cracked and shifted. The result is a gate that drags, won’t latch, or sits out of square.
The local climate makes it worse. Summers here are hot and dry, with temperatures that dry out and warp wooden gates and bake the finish off metal ones. The occasional Santa Ana wind event pushes gates hard against their hinges and latches, loosening hardware. Then the first fall rains arrive and unprotected iron starts rusting, while wood swells and sticks. Calls tend to peak after a heat snap and again after the first significant rain. A common situation on a Temple City visit is a 1950s iron gate whose original concrete post footing has cracked, so the hinge post has shifted and the gate drags against the walk. Fixing that properly means re-setting or shimming the post, not just adjusting the gate leaf. Homes in the 91780 ZIP code aren’t uniform either: newer infill and ADU construction has introduced modern aluminum and automatic gates next to the older ironwork, so we see both ends of the spectrum on the same block.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our Main Temple City Services
Most calls we get in Temple City fall into two categories: older gates that need structural repair, and newer automated systems that need electrical or mechanical diagnosis. Here’s how each one works.
Gate Repair in Temple City
This is the bread-and-butter call for Temple City’s older housing stock. A gate from the 1950s or 1960s has typically outlived its original hinges, latch, and sometimes its post footing. Our work involves re-hanging sagging gates, replacing rusted hardware, and re-setting posts that have shifted over decades. We match replacement parts to the era of the gate where possible, so the repair doesn’t look like an afterthought. The climate here means rust and heat-related warping are the two main culprits. Learn more about Gate Repair in Temple City.
Electric Gate Repair in Temple City
As newer construction and ADU projects have brought automatic gates to Temple City, the demand for competent electric diagnosis has grown. Automated gates fail differently than manual ones: the issue could be a control board, a limit switch, a low-voltage wiring fault, or a gear issue inside the operator. We work on the major brands and carry the diagnostic tools to identify the problem on the first visit. When a gate is half-open, beeping, or unresponsive, a generalist is guessing. We’re not. Details are on our Electric Gate Repair in Temple City page.
Gate Installation in Temple City
Installing a gate in Temple City usually means working with a specific set of conditions: a narrow front setback, an older concrete walk, and a house that was built before automatic gate operators existed. For newer properties, Gate Installation is straightforward. For the mid-century original gates, the work is more involved: removing the old iron, assessing whether the existing footing can be reused, and building a gate that suits a ranch-style home without looking out of place. We handle both manual and automated systems, so the same team that installs the gate can also run the power and set up the operator. This page covers Gate Installation in detail; Temple City specifics are below.
Automatic Gate Installation
Signs you need it
You’re adding a driveway gate to a property that never had one, or upgrading a manual gate to open and close without leaving the car.
What it costs in Temple City
Automatic gate installation in Temple City typically runs $3,000 to $9,500 depending on gate size, operator type, and the amount of low-voltage wiring needed between the gate and the house.
How we do it
We set the hinge and receiver posts at proper depth, hang the gate, mount the operator, run conduit and low-voltage wiring, and program the travel limits and safety inputs. Before any work starts we make sure you approve a written estimate, including the operator model.
Driveway Gate Installation
Signs you need it
You’re replacing an old wrought-iron driveway gate that’s rusted through, dragging, or no longer sized correctly for the driveway.
What it costs in Temple City
Driveway gate installation in Temple City ranges from $2,500 to $8,000 for the gate, posts, and hardware; automation adds to the total if it’s part of the scope.
How we do it
We remove the old gate and hardware, inspect the existing posts and footings, then set new posts and hang the gate with proper clearance for the ground and the driveway slope.
What Gate Installation Costs in Temple City
| Item | Typical range in Temple City |
|---|---|
| Automatic gate installation | $3,000 – $9,500 |
| Driveway gate installation | $2,500 – $8,000 |
| Electric gate installation (operator + gate) | $3,500 – $10,000 |
How long does a gate installation take in Temple City?
Most Temple City installs take one to two days for a straightforward driveway gate. An automatic system with a new operator, wiring, and concrete work can take two to three days, depending on access and the condition of the ground.
Do I need a permit to install a gate in Temple City?
Most cities require a permit for new driveway gate posts, especially if concrete is being poured. Ask Temple City’s building department before work starts. We don’t pull permits, but we’ll build to whatever the city requires.
Brands We Service in Temple City
We know BFT, Viking, Linear, and Ghost Controls systems inside Temple City before we arrive. The brand you have is not a surprise: we stock replacement parts for the common failure points and keep motors, boards, and remotes ready for same-week dispatch. If your system is running a less common setup, see our brands page for the full picture.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Company in Temple City, CA
| Service | Typical range in Temple City |
|---|---|
| Gate repair (hinge, latch, sagging gate) | $180 – $450 |
| Wrought-iron gate restoration (rust removal, paint, hardware) | $300 – $900 |
| Electric gate motor replacement | $650 – $1,800 |
| Control board replacement | $450 – $1,400 |
| Sliding gate repair | $250 – $700 |
| Automatic gate installation | $3,000 – $9,500 |
| Driveway gate installation | $2,500 – $8,000 |
| Electric gate installation | $3,500 – $10,000 |
What pushes a Temle City job higher is usually the condition of the post concrete, the length of low-voltage wiring needed to reach the house, or the need to remove a heavy iron gate that has rusted into its hinges. On the repairs side, we give a written estimate before work starts, and the price you approve is the price you pay: no surprise invoice after the fact.
Neighborhoods We Serve in Temple City
We cover all of Temple City, including the older residential blocks around the 91780 ZIP code. Our fast dispatch from 7am to 7pm, Sunday through Friday, typically means a repair visit can be scheduled within the day depending on call volume.
- Central Temple City
- North Temple City
- Southeast Temple City
- West Temple City
- East Temple City
Service Area – Cities Near Temple City
For gate work just outside Temple City, we also cover Rosemead, CA, San Gabriel, CA, Arcadia, CA, and Baldwin Park, CA. If your property is on the edge of Temple City and you’re not sure which page to use, call (855) 490-6590 and tell us the address. We’ll route you correctly and get a technician scheduled.
Serving Temple City, CA – Our Local Coverage Area
We serve Temple City and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs About Gate Company in Temple City
We answer 24/7 and dispatch technicians Sunday through Friday, 7am to 7pm. Same-day service is often possible for a Temple City repair call in the morning. A call outside dispatch hours is booked into the next opening, Sunday through Friday.
Yes. Automated and electric gates on HOA or multi-unit properties are core work for us. We coordinate directly with the property manager or board, provide a written estimate, and handle the diagnosis and repair without bouncing between unrelated trades.
We see this all over Temple City. If the original hinge or latch is no longer made, we’ll source a period-appropriate replacement or fabricate a workable modern equivalent. The goal is a gate that operates cleanly and looks like it belongs on the house.
Call (855) 490-6590 for a free estimate on any gate job in Temple City. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Your gate is your property’s first line of access control, and we treat it that way.
What happens when you call
- 1A real person answersNo phone trees. Talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3A background-checked tech heads outLicensed & insured, typically the same day.
- 4You approve before work beginsNothing starts until you say go.
What Temple City Customers Say
"Reprogrammed every clicker in the HOA and set up the keypad codes. Patient with a very long list of residents."
- Eric Miller"Photo eye was misaligned so the gate refused to close after dark. Ten minute fix. He also cleaned the lens and pointed out that the sprinkler head was spraying it every morning, which is why it kept happening."
- Craig Schaefer"Control board fried after a lightning storm. He showed me the burn mark on it, quoted the board, and installed a surge protector on the line so it hopefully doesn't happen again."
- Raj Sharma